Engineering/Mechanical Engineering Basic Mcq Questions Set 1 Sample Test,Sample questions

Question:
 A sine bar cannot be used without

1.Angle gauge

2.Vernier calliper

3.Slip gauge

4.Micrometer


Question:
 At half load the steam, consumption in the throttle governed engine is 'S1' and in a cut off governed engine it is 'S2' under similar condition

1. S2>S1

2.S2=S1

3.S2=S1/4

4.S2


Question:
 For machining the flange of a 90 elbow on a lathe, the following holding device is used.

1.Lathe dog

2.Catch plate

3. Angle plate

4.Face plate


Question:
 In a flange coupling, the flange bolts are designed for

1. fatigue

2. shear forces

3. compression

4. tensile forces


Question:
 In a mechanical refrigeration system, the highest temperature of refrigerant occurs

1.Between condenser and evaporater

2.In evaporator

3.Before expansion value

4.Between compressor and condenser


Question:
 In a process chart the inverted triangle symbol indicates

1.an operation

2. inspection

3.storage

4.transport


Question:
 In a simple spur gear train, gears with 24, 48, 32, 72 and 96 teeth are in sequence. The gear with 24 teeth runs at 900 rpm. The speed in rpm of gear with 72 teeth is

1.450

2.225

3.2700

4.300


Question:
 In upcut milling the work piece is fed

1. at angle of 60 deg to the cutter

2.against the rotating cutter

3.at the right angle to the cutter

4.in the direction of the cutter


Question:
 In vapour absorption refrigeration machine fluids used are

1.freon and lithium bromide

2.water and ammonia

3.brine and sulphur dioxide

4.air and water


Question:
 Kerosene is used as coolant, while machining

1. mild steel

2.cast iron

3.stainless stee

4.aluminium


Question:
 Pipes subjected to high pressures are generally made by

1. slush casting

2.pressure casting

3.extrusion

4.centrifugal casting


Question:
 Rapping allowance is provided on a pattern to take care of

1.shrinkage

2.distortion

3.machining

4.easy withdrawl


Question:
 The compression ratio of a petrol engine is approximately

1.3:1

2.7: 1

3.18:1

4.25:1


Question:
 The purpose of tumbler gears in lathe is to

1. Cut gears

2.Cut threads

3.Reduce spindle speeds

4.Give desired direction of movement to the lathe carriage


Question:
1.25 kg of hydrogen are burnt with stiochiometric air, the mass of air in kg required is (choose the nearest value)

1.10.0

2.21.6

3.435

4.48.6


Question:
A belt can transmit maximum power when the total tension of the drive is

1.equal to the centrifugal tension

2. twice the centrifugal tension

3. three times the centrifugal tension

4.four times the centrifugal tension


Question:
A cotter joint is generally used to transmit

1. torque

2.shear forces

3.tensile forces

4.bending forces


Question:
A feather key is on one the following types

1.sunk

2.tapered

3.parallel

4.tangent


Question:
a governer in an Ic engine controls the

1.mean speed variation

2.cyclic speed variation

3.load fluctuations

4.exhaust gas temperature


Question:
A lift descends with an acceleration of 0.5 metres/sec^2 from the top floor of a multistoried building. The time required to travel a distance of 25 metres will be

1. 5 sec

2.8 sec

3.10 sec

4.12 sec


Question:
A low wet bulb temperature indicates

1.cool air

2.cool air with high specific humidity

3.cool air with high enthalpy

4. cool air with low specific humidity


Question:
A mass of 40 kg is about to slide down when placed on a plane inclined at 30 degree to horizontal. The coefficient of friction between the plane and the mass is

1.3/2

2.2/3

3.1/3

4.4/3


Question:
A micrometer screw has pitch of 0.5 mm and the themble has 100 equal divisions marked on it, the least count of the instrument in mm is
. 

1.0.05

2.0.5

3. 0.025

4.0.005


Question:
A process in which no heat is supplied or rejected and entropy is constant is known as

1. adiabatic process

2.isentroic process

3. polytropic process

4.isothermal process


Question:
A simply supported beam has a uniformly distributed load on it, the bending moment diagram is

1.triangle

2.parabola

3.semicircle

4.rectangle


Question:
A stone of mass 1 kg tied to a string of 1 metre long is rotated in a horizontal circle at a constant angular speed of 5 rad/sec, then the tension in the string will be

1.5N

2.10N

3.15N

4.25N


Question:
Air fule ratio in a jet engine is

1.10:1

2.40:1

3.60:1

4.90:1


Question:
Air refrigeration cycle works on the

1.Brayton cycle

2.Bell Coleman cycle

3.Carnot cycle

4.Sterling cycle


Question:
Babbitt metal is an alloy of

1. tin, copper, antimony and lead

2.copper, zinc and tin

3.iron and tungsten

4.tin, copper, lead and phosphorous


Question:
Bore and stroke of a double acting steam engine cylinder are 30 cms and 50 cms respectively. If the IHP on crank end is 1% less than IHP on cover end, the diameter of piston rod is

1.1 cm

2.2 cm

3.3 cm

4.2.5 cm


Question:
Brasses and bronzes are welded using

1.neutral flame

2.oxidizing flames

3. carburising

4.reducing flame


Question:
Centrifugal tension in belt

1.Reduce power transmission

2.Increase power transmission

3.Does not effect power transmission

4.The effect is not definite


Question:
Centrifugal tension in belts results in

1. increased power transmission

2.reduced power transmission

3. increased belt velocity

4.same power transmission


Question:
Cobalt is added to high speed steel (H.S.S.) to

1.increase ductility

2.increase wear resistance

3.increases hot hardness

4.increase fatigue


Question:
Curtis turbine is a

1. pressure-compounded turbine

2.velocity-compounded turbine

3.pressure-velocity compounded turbine

4.reaction turbine


Question:
Draft on a pattern is provided for

1.facilitating pattern making

2.easy lifting of the casting

3. facilitating withdrawal of the pattern from the mould

4.providing for strinkage of the casting


Question:
During cold working, metals are worked

1.below their recrystalization temperature

2. below room temperature

3. below their melting point

4. below 200 degree celcius


Question:
Feed in a lathe is expressed in

1.mm per revolution

2.mm per degree

3.mm

4.rpm


Question:
Feeler gauges are used for measuring the

1.thickness of plates

2. clearances between mating parts

3. pitch of screw threads

4.radius of curvature


Question:
For a spring controlled governer the relation F = ar+b (F is the controlling force, r is the radius of rotation a and b are constants), indicates that the governer is

1.unstable

2.stable

3.insochronous

4.satisfactory


Question:
For cooling the pistons of diesel engine common fluid used is

1.air

2.water

3.fuel oil

4.lubricating oil


Question:
For gas turbines, the compressors used are

1.Reciprocating type

2.Centrifugal type

3.Axial flow type

4.Sliding value type


Question:
For the steam which is initially saturated andflowing through a nozzle, the ratio of pressures at exit and inlet for maximum discharge is equal to

1.0.545

2.0.582

3.0.5

4.0.6


Question:
Gnatt chart is used for

1. efficient machine utilisation

2.production scheduling

3. manpower utilisation

4.routing


Question:
If the acceleration due to gravity is doubled at any place, the weight of the body will be

1.half

2.double

3.same

4.2g times


Question:
In a carnot engine with an efficiency of 40%, the heat rejected to the sink at 27 C is 60 kJ, then the heat supplied in kJ to the engine by the sources is

1.24

2.56

3.100

4.50


Question:
In a lifting machine, a load of 240 N is being raised and the velocity ratio is 20. If the efficiency of the machine is 40%, the effort is equal to

1.20N

2.25N

3.30N

4.35N


Question:
In a typical lathe machining, discontinuous chips are formed when machining

1. carbon steel

2.copper

3.steel at high speed

4.mild steel


Question:
In Industry of the developed nations the type of production most often occurring is

1.Mass production

2.Batch production

3.Single lot production

4.Create lot production


Question:
In power transmission using open belts or horizontal shafts it is preferable to have the slack side of the belt on the top because

1.the belt length is smaller

2.the slip is more

3. the angle of contact is more

4.it is safe


Question:
In V-belts the contact between the pulley and the belt is at the

1.Bottom only

2.Both side and bottom

3.Top and bottom

4.Sides only


Question:
In vapour compression refrigeration system, compressor is used because

1. It increases cooling effect of cycle

2. It makes possible, to remove heat from refrigerant at atmospheric pressure

3.It increases the coefficient of performance of the system

4. It removes thermal properties of refrigerant


Question:
Mandrels are used to hold

1.cutting tools

2.hollow work pieces

3.face plate

4.drill bits


Question:
Newton is a unit of

1.Mass

2.Momentum

3.Force

4.Energy


Question:
One of the following materials is comonly used for bearings

1.steel

2.gun metal

3.zinc

4.aluminium


Question:
One of the following objectives is not achieved by the process of annealing

1.to relieve internal stress

2.to refine grain structure

3. to increase the yield point

4.to soften the metal


Question:
One of the materials used for making surface plate is

1.granite

2.brass

3.stainless steel

4.wood


Question:
Permeability, in relation to moulding sands, is high for

1.coarse grains

2.fine grains

3.round grains

4.medium grains


Question:
Quick return motion is used in a

1.lathe

2.drilling

3.shaper

4.grinder


Question:
Reducing flame is obtained in oxyactetylane welding with

1.excess oxygen

2. equal parts of both gases

3.excess of acetylene

4. reduced acetylene


Question:
Sprue is the passing provided for the

1.outflow

2.smooth flow

3.inflow

4.solidification of the molten material


Question:
The centrifugal tension in belts

1. increase power transmission

2.decrease power transmission

3.doubles the power transmission

4.does not affect the power transmission in any way


Question:
The coefficient of Performance for a refrigerator will be

1.0.001

2.0.10

3.1.00

4.above 1.0


Question:
The dimensional formula MLT^2 represents

1.velocity

2.acceleration

3.momentum

4.force


Question:
The function of a carburettor is to supply

1. air and diesel

2.air only

3.air and petrol

4.petrol


Question:
The moisture in air will condense at

1.wet bulb temperature

2.low point temperature

3.saturaion temperature

4.dry bulb temperature


Question:
The operation of enlarging of a hole is called

1.drilling

2.reaming

3.boring

4.counter sinking


Question:
The part which provides simple harmonic to the D-slide valce of a steam engine is called

1.eccentric rod

2.valve rod

3.piston rod

4.fly wheel


Question:
The pump with a low initial cost and low maintenance cost is

1.gear pump

2.bucket pump

3.double acting piston pump

4.centrifugal pump


Question:
The refrigerant used in vapour absorption refrigeration
 

1.Freon-12

2.ammonia

3.O2

4.Aqua-ammonia


Question:
The screw thread commonly used for transmission of motion is one of the following types of threads

1.acme

2.vee

3.knuckle

4. British Association


Question:
The tool life is affected to the maximum extent by

1.the cutting speed

2.the feed

3. the depth of cut

4.the size of the tool


Question:
The unit of energy is S.I. system is

1.Newton

2.Pascal

3.Joule

4.Watt


Question:
To produce a spark across the gap of a spark plug, the voltage used is

1.1000 to 2000 volts

2.2000 to 4000 volts

3.4000 to 6000 volts

4.6000 to 10000 volts


Question:
Two forces of magnitude 30 N and 40 N act at right angles at a point, the magnitude of the resultant force is

1.50N

2.10N

3.70N

4.35N


Question:
Two masses of 10 gm and 4 gm are moving with equal kinetic energy. The ratio of their linear momentum is

1.1:2

2. 3:1

3.4:1

4.1:16


Question:
Upsetting is the term used in one of the following operations

1.casting

2.turning

3.drilling

4.forging


Question:
Which of the following operations cannot be performed on a lathe

1.facing

2.drilling

3. thread cutting

4.slotting


Question:
Which one of the following is not part of combination set?

1.Try square

2.Scale

3. Bevel Protractor

4.Dial guage


Question:
Which one of the following is spring loaded type
A. B.C.D. 

1.Watt governor

2. Hartnel governor

3. Porter governor

4.Propel governor


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
  106. Basic Civil Engineering MCQ
Search
Olete Team
Online Exam TestTop Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on Online Exam Testwebsite is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!