Gate/GATE Agricultural Engineering Set 2 Sample Test,Sample questions

Question:
 A two-wheel drive tractor weighing 21 kN has a wheel base of 2.1 m. The CG of the tractor is 0.7 m ahead of rear axle centre. The tractor is pulling a single-axle trailer with gross trailer weight of 50 kN on a leveled concrete road while maintaining the line of pull parallel to the ground surface. The tractor hitch point is 42 cm behind the rear axle centre and 52.5 cm above the ground surface. During operation, 20% of the gross trailer weight is transferred to the tractor hitch point. If the coefficient of rolling resistance for each of the tractor and trailer wheels is taken as 0.04, and their ground reactions are assumed to pass through their respective wheel centres, 
the gross traction ratio developed by the tractor is

1.0.061

2.0.082

3.0.108

4.0.123


Question:
 During a test, sound level was measured as 90 dB in the operator's cabin on a tractor. Taking reference sound pressure as 2 * 10-5 N m-2, the measured RMS sound pressure in N m-2 is

1.6.32

2.6.32 * 10-1

3.1.8 * 10-3

4. 6.32 * 10-10


Question:
 If the drainable porosity of a command area is 5% and the design rate of drop of the water table is 0.25 m day-1, the drainage coefficient of the command area in mm day-1 will be

1.250

2.12.5

3.1.25

4.0.0125


Question:
 In a factory, two machines M1 and M2 manufacture 60% and 40% of f |-2X + 9| = 3 then the possible value of |-X| - X2 would be:

1.30

2.-30

3.-42

4.42


Question:
 In a screen separator, the mass flow rates of feed, overflow and underflow are 150, 140 and 10 kg h-1, respectively. Mass fraction of material in the feed and overflow are 0.9 and 0.96, respectively. The effectiveness of separation in percentage is

1.32

2.42

3.52

4.62


Question:
 The Rational method is used to estimate

1.runoff volume

2.peak runoff rate

3. runoff depth

4.direct surface runoff


Question:
 Velocity of an object fired directly in upward direction is given by V = 80 − 32 t, where t (time) is in seconds. When will the velocity be between 32 m/sec and 64 m/sec?

1.( 1, 3/2)

2. (1/2, 1)

3.(1/2, 3/2)

4.(1, 3)


Question:
A 10 ha field has 1.2 m deep layer of sandy loam soil underlain by sandy soil up to a depth of 5 m. A pre-irrigation rainfall brings moisture content of the top 0.3 m layer to its field capacity. The moisture content of rest of the sandy loam layer remains at permanent wilting point. The volumetric moisture content at field capacity and permanent wilting point are 32 and 16%, respectively for the sandy loam soil. The field is irrigated with a stream size of 240 L s-1 for 24 hours. Considering the drainage from the sandy loam soil as deep percolation, application efficiency and deep percolation ratio in percent respectively are

1.56.40 and 43.60

2.69.44 and 30.56

3.75.18 and 24.82

4.92.60 and 7.40


Question:
A 100 ha watershed received rainfall at a rate of 5 cm h-1 for 2 hours. If the runoff generated by the storm was at the rate of 1 m3 s-1 for 10 hours, the runoff coefficient for the watershed would be

1.3.6 * 10-3

2.6.0 * 10-5

3. 0.36

4.36


Question:
A 16 m high wind break is constructed to protect soil from wind erosion due to wind velocity of 18 m s-1 at 15 m height. The minimum wind velocity at 15 m height capable of moving the soil fraction is 8 m s-1. The angle of deviation of prevailing wind direction from the perpendicular to the wind break is 300. The distance of full protection from the wind break in m is

1.60.44

2.104.69

3. 306.00

4.530.01


Question:
A 4-cylinder, 4-stroke compression ignition engine has piston stroke of 10.5 cm and cylinder bore of 11 cm. At a mean piston speed of 7 m s-1, the developed brake mean effective pressure is 650 kPa. The brake power in kW developed by the engine is

1.39.40

2.43.24

3.86.48

4.172.96


Question:
A 9 * 20 cm fluted roller type seed drill is operated at a forward speed of 3 km h-1 in a field of size 120 m * 90 m. The effective ground wheel diameter of the seed drill is 0.5 m and the ratio of ground wheel rpm to the fluted roller rpm is 2. For one complete rotation of each fluted roller, 6.8 g seed is transferred from the seed box to the seed tube. The average time taken for each turn while operating length-wise is 50 s and the total time wasted in refilling the seed box for sowing the entire field is 40 min. 
The actual field capacity of the machine in ha h-1 is

1.0.30

2.0.32

3.0.36

4.0.40


Question:
A 9 * 20 cm fluted roller type seed drill is operated at a forward speed of 3 km h-1 in a field of size 120 m * 90 m. The effective ground wheel diameter of the seed drill is 0.5 m and the ratio of ground wheel rpm to the fluted roller rpm is 2. For one complete rotation of each fluted roller, 6.8 g seed is transferred from the seed box to the seed tube. The average time taken for each turn while operating length-wise is 50 s and the total time wasted in refilling the seed box for sowing the entire field is 40 min. 
The actual field capacity of the machine in ha h-1 is

1.0.30

2.0.32

3.0.36

4.0.40


Question:
A 9 * 20 cm fluted roller type seed drill is operated at a forward speed of 3 km h-1 in a field of size 120 m * 90 m. The effective ground wheel diameter of the seed drill is 0.5 m and the ratio of ground wheel rpm to the fluted roller rpm is 2. For one complete rotation of each fluted roller, 6.8 g seed is transferred from the seed box to the seed tube. The average time taken for each turn while operating length-wise is 50 s and the total time wasted in refilling the seed box for sowing the entire field is 40 min. 
The seed rate in kg ha-1 will be

1.108.32

2.122.55

3.136.99

4.240.71


Question:
A 9 * 20 cm fluted roller type seed drill is operated at a forward speed of 3 km h-1 in a field of size 120 m * 90 m. The effective ground wheel diameter of the seed drill is 0.5 m and the ratio of ground wheel rpm to the fluted roller rpm is 2. For one complete rotation of each fluted roller, 6.8 g seed is transferred from the seed box to the seed tube. The average time taken for each turn while operating length-wise is 50 s and the total time wasted in refilling the seed box for sowing the entire field is 40 min. 
The seed rate in kg ha-1 will be

1.108.32

2.122.55

3.136.99

4.240.71


Question:
A centrifugal pump having an overall efficiency of 75% requires 6 kW power at 1450 rpm to deliver water against a suction head of 5 m and a delivery head of 12 m. If the pump runs at 1650 rpm and frictional head losses are negligible, the total head developed by the pump in metres will be

1.22.01

2.25.05

3.29.35

4.31.72


Question:
A cold storage chamber is constructed with 10 mm mortar, 200 mm brick, 100 mm insulation and 5 mm wood-board having thermal conductivities of 0.8, 1.5, 0.025 and 0.2 W m-1 K-1, respectively. The resistance of 4 K m-1 W-1 is offered by

1.mortar

2.brick

3.insulation

4.wood-board


Question:
A double acting hydraulic cylinder has a rod diameter equal to one-half the piston diameter. If the system pressure is maintained constant, the ratio of load carrying capacity of extension stroke to that of retraction stroke is

1.0.75

2.1.00

3.1.33

4.4.00


Question:
A fish fillet of 5 mm thickness having 85% moisture (wet basis) is to be frozen using a plate freezer. The plates are at -350C and the heat transfer coefficient between the fillet and the freezer plates can be assumed to be 2.0 W m-2 K-1. The initial freezing temperature of fish is -2.50C, latent heat of fusion is 330 kJ kg-1, density of fish is 1100 kg m-3 and thermal conductivity of frozen fish is 1.5 W mm-1 K-1. The time required to freeze the fillet from the initial freezing temperature in hour(s) is __________

1. 6.25 to 6.35

2.5.25 to 5.35

3. 4.25 to 4.35

4.3.25 to 3.35


Question:
A hemispherical vessel of 300 mm diameter is completely filled with oil and water. If the oil layer is 50 mm deep on the top, the volume of water in the vessel in litres is

1.1.27

2.3.73

3.7.07

4.14.14


Question:
A high pressure dairy homogenizer operates under upstream and downstream pressures of 200 and 40 bar respectively homogenizing 30 L of whole milk per hour. Density and specific heat capacity of whole milk are 1030 kg m-3 and 3.8 kJ kg-1 K-1, respectively. Assuming complete energy conservation, the temperature rise of whole milk in degree Celsius is _______________

1.3.2 to 3.4

2.4.7 to 4.9

3.4 to 4.2

4.2.4 to 2.6


Question:
A milk fat globule of 2 μm diameter is rising in whole milk of density 1030 kg m-3 and coefficient of viscosity 10-3 Poise. If the fat density is 950 kg m-3, the time needed to rise 10 mm for this fat globule in min is

1.0.57

2.34.57

3.35.57

4.95.57


Question:
A milk fat globule of 2 μm diameter is rising in whole milk of density 1030 kg m-3 and coefficient of viscosity 10-3 Poise. If the fat density is 950 kg m-3, the time needed to rise 10 mm for this fat globule in min is

1.0.57

2.34.57

3.35.57

4.95.57


Question:
A piston pump is driven by a 5 m diameter horizontal axis wind turbine for supplying water from a borehole with a total pump head of 10 m. The mean velocity of air is 18 km h-1 and the density of air is 1.29 kg m-3. The actual power coefficient of the wind turbine is 0.30 and the overall pump efficiency is 60%. Neglecting the transmission losses, the expected pump discharge in L s-1 will be

1.2.90

2.5.80

3.28.50

4.32.27


Question:
A rotary dryer is used to dry 1200 kg h-1 of paddy containing 30% moisture (wet basis) to give a product containing 15% moisture (wet basis). Alternately, a portion of the dry product may be recycled and mixed with the fresh feed such that the mixed feed enters the dryer with moisture content of 20% (wet basis). The moisture evaporation rate without recycle and the paddy recycle rate in kg h-1 respectively in the dryer are

1.211.76 and 2400

2.211.76 and 600

3.256.5 and 2400

4.256.5 and 600


Question:
A soil has a void ratio of 0.75 and a specific gravity of 2.66. The value of critical hydraulic gradient at which quick sand condition will occur is

1.0.95

2.1.05

3.2.09

4.6.64


Question:
A tractor mounted off-set type reciprocating mower is driven by the PTO shaft. The maximum inertia force of 3.2 kN occurs along the pitman at 320 crank angle and 270 pitman angle with the horizontal plane. The knives of the cutterbar are riveted to the slider. If each of the allowable tensile and compressive stresses of the slider material is 50 MPa, the minimum cross-sectional area of the slider in mm2 is

1.29.05

2.33.91

3.54.27

4. 57.02


Question:
A tractor operated single acting trailing type disc harrow has 8 discs on each gang. The gang angle of both the gangs is maintained at 350. The horizontal component of resultant soil reaction force on each disc is 600 N and it makes an angle of 300 with the gang axis. If the speed of operation is 6 km h-1, the required drawbar power in kW to operate the harrow will be _______________

1.12.3 to 12.5

2.14.4 to 14.6

3.24.4 to 24.6

4.14.2 to 14.4


Question:
A two-wheel drive tractor pulls an implement that has a draft force of 11.5 kN. The total motion resistance of the tractor is 2.5 kN. Under these circumstances, the slip of the drive wheels is 20%. If the power loss in transmission is 20%, the percentage of power lost in converting engine power into drawbar power is _______________

1.47.4 to 47.5

2.24.3 to 24.4

3.12.7 to 12.8

4. 45.5 to 45.6


Question:
A two-wheel drive tractor weighing 21 kN has a wheel base of 2.1 m. The CG of the tractor is 0.7 m ahead of rear axle centre. The tractor is pulling a single-axle trailer with gross trailer weight of 50 kN on a leveled concrete road while maintaining the line of pull parallel to the ground surface. The tractor hitch point is 42 cm behind the rear axle centre and 52.5 cm above the ground surface. During operation, 20% of the gross trailer weight is transferred to the tractor hitch point. If the coefficient of rolling resistance for each of the tractor and trailer wheels is taken as 0.04, and their ground reactions are assumed to pass through their respective wheel centres, 
the dynamic ground reaction against the tractor rear wheels in kN is

1.14.0

2.24.0

3.24.5

4.26.4


Question:
A two-wheel drive tractor, while negotiating a terrain, indicates 100% slip of one of the rear wheels. Under such a condition, the use of differential lock causes

1.equal speed and equal power distribution to both the drive wheels

2.equal speed and equal torque distribution to both the drive wheels

3.equal power and equal torque distribution to both the drive wheels

4.equal speed and unequal power distribution to both the drive wheels


Question:
A watershed, with an area of 360 km2, has a triangular shaped 4-h unit hydrograph with a base of 50 hours. The peak discharge of direct runoff hydrograph due to 3 cm of rainfall-excess in 4 hours from the watershed in m3 s-1 is

1.13.33

2.14.00

3.120.00

4.160.00


Question:
All engineering students should learn mechanics, mathematics and how to do computation. 
                     I                                         II                                     III                                IV 
Which of the above underlined parts of the sentence is not appropriate?

1.I

2.II

3.III

4.IV


Question:
An unconfined aquifer extends over an area of 1 m2 and has hydraulic conductivity, total porosity and specific retention of 20 m per day, 30% and 10%, respectively. After pumping some groundwater from this aquifer, the water table dropped to a depth of 20 m from the ground level. If the water table was initially at 14.5 m below the ground level, the change in groundwater storage in million cubic meters would be _______________

1.110000

2.1200000

3.120000

4. 1100000


Question:
Box 1 contains 15 balls out of which 3 are red. Box 2 contains 12 balls out of which 4 are red. If one ball is drawn at random from each box simultaneously, the probability of getting at least one red ball is

1.0.07

2.0.47

3. 0.53

4.0.75


Question:
During land leveling of agricultural land for irrigation and drainage purposes, the acceptable deviation in elevation from the design value in metre is

1.0.015

2.0.025

3.0.055

4. 0.0150


Question:
During the testing of a spike-tooth type thresher for wheat crop, the throughput and the thresher capacity were found to be 750 kg h-1 and 445 kg h-1, respectively. The grain-straw ratio (grain : straw) of the crop is 1.5 : 1. Material other than grain (MOG) collected at the main grain outlet is 0.5%. The total grain loss in percentage from all the sources will be

1.0.33

2.0.50

3.1.11

4.1.61


Question:
For an initial spore load equal to 25 spores per container inoculated with Clostridium botulinum having D121 = 0.25 min, the spoilage probability of the container subjected to F121 = 1.5 min is

1.10-5

2.10-6

3.10-8

4.10-9


Question:
If 3 ≤ X ≤ 5 and 8 ≤ Y ≤ 11 then which of the following options is TRUE?

1.3/5 ≤ X/Y ≤ 8/5

2.3/11 ≤ X/Y ≤ 5/8

3.3/11 ≤ X/Y ≤ 8/5

4.3/5 ≤ X/Y ≤ 8/11


Question:
If C = A×B , where A = 2i - j + 3k and B = i + 2j ; then C is

1. -6i + 3j + 5k

2.6i + 3j "“ 5k

3.-6i + 2j + 3k

4.6i + 2j + 5k


Question:
In a screen separator, the mass flow rates of feed, overflow and underflow are 150, 140 and 10 kg h-1, respectively. Mass fraction of material in the feed and overflow are 0.9 and 0.96, respectively. The effectiveness of separation in percentage is

1.32

2.42

3.52

4.62


Question:
In an experimental setup, the discharge through a triangular notch is 0.0074 m3 s-1 at an operating head of 0.1 m. The coefficient of discharge for the notch is 0.7. If the required discharge is 0.1 m3 s-1 
the corresponding head in m is

1.0.00015

2. 0.035

3.0.283

4.67.13


Question:
In an experimental setup, the discharge through a triangular notch is 0.0074 m3 s-1 at an operating head of 0.1 m. The coefficient of discharge for the notch is 0.7. If the required discharge is 0.1 m3 s-1 
the corresponding width of water surface in m is

1.0.80

2.0.099

3.0.00043

4.0.00086


Question:
Mahatama Gandhi was known for his humility as

1. he played an important role in humiliating exit of British from India.

2.he worked for humanitarian causes.

3.he displayed modesty in his interactions.

4.he displayed modesty in his interactions.


Question:
Milk enters into the heating section of a high temperature short time (HTST) pasteurization plant at a temperature of 45ºC and leaves at 72ºC. Hot water at temperature of 95 ºC enters countercurrently into the heat exchanger and leaves at 77ºC. The effectiveness of the heat exchanger is

1.0.18

2.0.36

3.0.54

4.0.84


Question:
Pan evaporation data recorded at a certain location over a period of one week are 4.0, 4.3, 4.6, 4.9, 5.12, 5.18, and 6.21 mm. If irrigation scheduling based on ratio of irrigation water (IW) to cumulative pan evaporation (CPE) is practiced, the depth of irrigation at an interval of a week for IW/CPE = 0.9 is

1.3.60

2. 4.41

3.5.59

4. 30.88


Question:
Poisson distribution having a mean of 5 will have √5 as

1.median

2.mode

3.standard deviation

4.variance


Question:
Select the pair that best expresses a relationship similar to that expressed in the pair: water: pipe::

1.cart: road

2.electricity: wire

3.sea: beach

4.music: instrument


Question:
Slope and intercept of the BET equation relating [aw/x(1 - aw)] and aw, where aw is water activity and x is the moisture content on dry basis, are 18 and 2, respectively. The values of thermodynamic constant C and BET monolayer moisture content xm(%) are respectively

1.40 and 20

2.30 and 15

3.20 and 10

4.10 and 5


Question:
Specific heat capacity of dry air and water vapour are 1.005 and 1.88 kJ kg-1 K-1, respectively. In an energy conserving system, 1 kg s-1 air at 300C with constant absolute humidity of 0.02 kg water (kg dry air)-1 is heated up to 650C. Water at the wet bulb temperature of air is then sprayed into the air so that the final temperature of the air-water vapour mixture is 400C. Latent heat of vapourization of water at 700C and 400C are 2334 and 2407 kJ kg-1, respectively. 
The absolute humidity of the exhaust air from the spray chamber in kg water (kg dry air)-1 is

1.0.027

2.0.029

3.0.031

4.0.033


Question:
Specific heat capacity of dry air and water vapour are 1.005 and 1.88 kJ kg-1 K-1, respectively. In an energy conserving system, 1 kg s-1 air at 300C with constant absolute humidity of 0.02 kg water (kg dry air)-1 is heated up to 650C. Water at the wet bulb temperature of air is then sprayed into the air so that the final temperature of the air-water vapour mixture is 400C. Latent heat of vapourization of water at 700C and 400C are 2334 and 2407 kJ kg-1, respectively. 
The thermal energy supplied per second during heating in kW is

1.18.2

2.36.5

3.101.0

4.166.8


Question:
Specific heat capacity of dry air and water vapour are 1.005 and 1.88 kJ kg-1 K-1, respectively. In an energy conserving system, 1 kg s-1 air at 300C with constant absolute humidity of 0.02 kg water (kg dry air)-1 is heated up to 650C. Water at the wet bulb temperature of air is then sprayed into the air so that the final temperature of the air-water vapour mixture is 400C. Latent heat of vapourization of water at 700C and 400C are 2334 and 2407 kJ kg-1, respectively. 
The thermal energy supplied per second during heating in kW is

1.18.2

2.36.5

3.101.0

4.166.8


Question:
The cumulative discharge of a tractor mounted hydraulic sprayer having 7 nozzles is 2.0 L min-1 when the tractor is operated at 4 km h-1. If the nozzle spacing is 0.3 m, the discharge in L ha-1 is

1.1000.02

2.285.72

3. 166.67

4.142.86


Question:
The equation representing the heat of respiration (q) of fruits and vegetables as a function of temperature (θ) with positive constants a and b is

1.q = aebθ

2.q = ae-bÃŽ

3.q = a ln(bθ)

4.q = a + bθ


Question:
The flywheel of a hand operated chaff cutter with two cutting knives is rotated at 30 rpm and is connected to a worm gear assembly for driving the feed rollers. The number of teeth of the worm gear is 24 and number of starts (threads) of the worm is 2. If diameter of each of the feed rollers is 15 cm, the chaff length in mm will be

1. 9.8

2. 12.8

3.19.6

4.39.2


Question:
The general solution of the differential equation d2y/dx2 -3 dy/dx - 4y = 0 is

1.Aex + Be-4x

2.Ae-x + Be4x

3.Aex + Be-4x

4. Ae-x + Be-4x


Question:
The gridiron pipe drainage system is more economical than the herringbone pipe drainage system because

1.it is adopted in the fields which do not require complete drainage

2.the number of main or sub-main lines is reduced

3.the number of junctions and the double-drained area are reduced

4.it has only main or sub-main lines


Question:
The Headmaster ___________ to speak toyou. 
Which of the following options is incorrect to complete the above sentence?

1.is wanting

2.wants

3.want

4.was wanting


Question:
The horse power of the motor running the compressor of a refrigerator having COP of 4.5 and extracting 200 kJ kg-1 of evaporating heat with 1.5 kg min-1 refrigerant flow rate is

1.0.5

2.1.0

3.1.5

4.2.0


Question:
The overall heat transfer coefficient based on the outside surface area of a tubular heat exchanger decreased due to fouling during operation from 1000 W m-2 K-1 to 800 m-2 K-1. The fouling film coefficient of the heat exchanger in m-2 K-1 is _______________

1.4000

2.4100

3.4200

4.4300


Question:
The pressure that does not have any measurable influence on the void ratio or shearing resistance of the soil mass is

1. pore water pressure

2. intergranular pressure

3.capillary pressure

4.surcharge pressure


Question:
The rear furrow wheel in a tractor mounted disc plough is provided to

1. reduce the frictional power loss

2.maintain the uniform depth of cut

3.reduce the side draft

4.improve the penetration of the plough


Question:
The work index of a material is 6.25. If 80% of the feed and 80% of the product pass through IS Sieve No. 340 (3.25 mm opening) and IS Sieve No. 40 (0.42 mm opening), respectively, the power consumed in kW to crush 5000 kg h-1 of sorghum is

1.9.77

2.20.49

3.26.29

4.32.29


Question:
Two parallel canals 50 m apart fully penetrate a homogeneous unconfined aquifer resting on a horizontal impermeable layer. The aquifer has a hydraulic conductivity of 3 m day-1 and an effective porosity of 0.25. One-dimensional steady groundwater flow occurs from the upper canal to the lower canal with the height of water levels in the canals 10 m and 8.5 m from the aquifer bottom, respectively. If a sediment layer of 4 cm thick with hydraulic conductivity of 1.2 * 10-2 m day-1is ultimately deposited on the inflow face, the groundwater discharge per 1000 m width between the two canals in m3 day-1 will be _______________

1.620 to 625

2. 665 to 670

3. 690 to 695

4. 700 to 705


Question:
vSpecific heat capacity of dry air and water vapour are 1.005 and 1.88 kJ kg-1 K-1, respectively. In an energy conserving system, 1 kg s-1 air at 300C with constant absolute humidity of 0.02 kg water (kg dry air)-1 is heated up to 650C. Water at the wet bulb temperature of air is then sprayed into the air so that the final temperature of the air-water vapour mixture is 400C. Latent heat of vapourization of water at 700C and 400C are 2334 and 2407 kJ kg-1, respectively. 
The absolute humidity of the exhaust air from the spray chamber in kg water (kg dry air)-1 is

1.0.027

2.0.029

3.0.031

4.0.033


More MCQS

  1. Engineering GATE 2017-2018 Aeronautical
  2. GATE 2017-2018 Aeronautical
  3. Engineering GATE 2017-2018 EEE
  4. GATE 2017-2018Architecture and Planning
  5. GATE 2017-2018 Architecture and Planning Practice Paper 2
  6. GATE 2017-2018 Metallurgical
  7. GATE Textile and Fiber Science Set 1
  8. GATE Textile and Fiber Science Set 2
  9. GATE 2017-2018 Biotechnology Set 1
  10. GATE 2017-2018 Biotechnology Set 2
  11. GATE Geology and Geophysics
  12. GATE Geology and Geophysics Set 2
  13. GATE Agricultural Engineering Set 1
  14. GATE Agricultural Engineering Set 2
  15. GATE Civil Engineering
  16. GATE ECE Mcq
  17. GATE Mechanical Mcq
  18. GATE Mechanical Mcq Set-2
  19. GATE Mining Engineering Mcq
  20. GATE Production and Industrial
  21. GATE STUDY MATERIAL /COMPUTER ARCHITECTURE MCQ SET 1
  22. GATE STUDY MATERIAL /COMPUTER ARCHITECTURE MCQ SET 2
  23. GATE STUDY MATERIAL /COMPUTER ARCHITECTURE MCQ SET 3
  24. GATE STUDY MATERIAL /DBMS SET 1
  25. GATE STUDY MATERIAL /DBMS SET 2
  26. GATE STUDY MATERIAL /NETWORKING SET 1
  27. GATE STUDY MATERIAL /NETWORKING SET 2
  28. GATE STUDY MATERIAL /NETWORKING SET 3
  29. Gate Logic MCQ Question & Answers
Search
Olete Team
Online Exam TestTop Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on Online Exam Testwebsite is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!