SPI is alternatively called _____?
1.4-wire serial bus
2.3-wire serial bus
3. 2-wire serial bus
4. All the above
In which form electrically coded data is transferred in SPI?
1.Bit by Bit
2.Bulk
3.Parallel
4.Both a and b
In which of the following form digital data is converted before transmitting to microcontroller?
1.1 byte
2.8 bits
3.Binary word
4.All of the above
MOSI has data ____ from master?
1.In
2.Out
3.Both a and b
4.None of the above
SPI stands for _____?
1.Serial Peripheral Interface
2.Side Peripheral Interface
3.Serial Parallel Interface
4.None of the above
A master component in SPI architecture is also called ___?
1.Controller
2.Selector
3.Rotor
4.None of the above
A SPI has ____ number of slave components?
1.1
2.2
3.3
4.Multiple
A SPI is used for ____ length distance communication?
1. Short
2.Long
3.Medium
4.Zero
A SPI pose ____ type of serial communication interface?
1.Synchronous
2.Asynchronous
3.Duplex
4.None of the above
An SPI is ____ communication type BUS?
1.Serial
2.Full-duplex
3.Half-duplex
4.Both (a) and (b)
Bits communicated between devices is due to changes in ______ parameter?
1.Current
2.Voltage
3.Inductance
4.Resistance
CS in SPI architecture stands for _____?
1.Chip select
2.Cut select
3.Chord select
4.All of the above
From which of the following component SCLK receives input?
1.Master
2.Slave
3.Both a and b
4.None of the above
How many logic signals does an SPI bus has?
1.1
2.2
3.3
4.4
How many master components does an SPI bus architecture has?
1.1
2.2
3.3
4.4
LCD stands for ____?
1.Liquid Crystal Display
2.Liquid Crystal Diode
3. Light Crystal Display
4.None of the above
MISO stands for?
1.Master In Slave Out
2.Mute In Slave Out
3.Master In Side Out
4.None of the above
MOSI in SPI architecture stands for?
1.Master Out Slave In
2. Must Out Slave In
3.Master Out Side In
4.None of the above
SCLK in SPI bus architecture stands for ____?
1.Serial clock
2.Side clock
3.Silent clock
4.None of the above
SCLK is the data _____ in SPI bus architecture?
1.Output
2.Input
3.Both a and b
4.None of the above
Speed of ______ which parameter is identified by frequency of clock signal.
1. Data receive
2.Data transfer
3.Receiving information
4. None of the above
SPI bridges between MC’s and sensors where high amounts of high____ parameter data will not be transferred.
1.istance
2.speed
3. Time
4.Quantity
SPI bus is different from ____ protocol?
1.SSI
2.SIP
3.TCP
4.IP
SPI is a bit ______ than other protocols like USB, Ethernet.
1.High
2.Low
3.Slower
4.Faster
SPI protocol is used in ___ field of engineering?
1.Embedded system
2.Digital system
3.Mechanical system
4.All of the above
The number of slaves is limited by loads _______ property of the system.
1.Inductance
2.Capacitance
3.Resistance
4.Voltage
The rate of transmission is also called ____?
1. Baud rate
2.Speed rate
3. Accelerate rate
4.None of the above
The serial type data in an embedded system is transmitted to its peripheral devices depending on ____?
1.Clock
2.Devices
3.BUS
4.Protocols
The serial type data in an embedded system is transmitted to its peripheral devices depending on ____?
1.Clock
2.Devices
3.BUS
4.Protocols
What is the total size of transmitted data in bits/sec, when 12 bytes of data is transmitted?
1.90
2.96
3.99
4.100
When one device is used in SPI architecture which pin is set low?
1.SS
2.CE
3. CS (bar)
4.None of the above
Which of the following are chip select pins in SPI?
1.SS,SS(bar)
2.CS, CS (bar)
3.CE
4.All the above
Which of the following are serial communication type protocols?
1.UART
2.CAN
3. SPI
4.All of the above
Which of the following are slave select pins in SPI?
1.SS,SS(bar)
2.CS, CS (bar)
3.CE
4.All of the above
Which of the following are the characteristic of serial communication protocol?
1.Greater speed
2.Less data loss
3.Less complex design
4.All of the above
Which of the following are the communication components of embedded systems?
1.Controllers
2.Sensors
3.Actuators
4.All of the above
Which of the following are the components of SPI in full duplex mode?
1.Master
2.Slave
3.Both a and b
4.None of the above
Which of the following are the control signals of MISO?
1.SOMI,MTSR
2.SDI, DI, DIN, SI
3.SDO, DO, DOUT, SO
4.All of the above
Which of the following are the control signals of MOSI?
1.SIMO, MTSR
2.SOMI, MRST
3.SDI, DI, DIN
4.both a and b
Which of the following are the properties of SSI protocol?
1.Variant signaling
2.Simplex communication
3.Zero delay
4.Both a and b
Which of the following is the limitation in absence of protocol bus?
1.More complex
2.More power consumption
3.Difficult in design
4.All the above
Which of the following is the quantity of a SSI protocols simplex communication?
1.1
2.2
3.3
4.4
Which of the following is the type of communication used in embedded system?
1.Serial
2.Parallel
3. Concurrent
4.Both a and b
Which of the following is the typical application of SPI?
1. LCD
2.Secure digital cards
3.Embedded systems
4.All the above
Who developed SPI interface?
1.Motorola
2.Samsung
3.LG
4.Intel
__ is the terms used for picking up a particular slave in a SPI master and slave architecture?
1.Chip select
2.Slave select
3.Master select
4.Both a and b
____ bit is communicated as a short type pulse of 0 volts.
1.2
2.1
3.0
4.None of the above
____ bit is communicated as a short type pulse of 0 volts.
1.2
2.1
3.0
4.None of the above
____ is also represents serial data?
1.Electrically coded
2.Mechanical arranged
3.Both a and b
4.None of the above
_____ Module uses SPI to communicate data with MC’s.
1.RFID card reader
2.Master card reader
3.Slave card reader
4.Parallel card reader