Engineering/Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4 Sample Test,Sample questions

Question:
 
Plasticity index is defined as the range of water content between

1.liquid and plastic limit

2.plastic limit and semi solid limit

3.semi-solid limit and liquid limit

4.liquid limit and solid limit.


Question:
 
The shear strength in plastic undrained clay, is due to

1.inter-granular friction

2. internal friction

3.cohesion

4. none of these.


Question:
  
A pycnometer is used to determine

1.density index.

2.water content

3.dry density

4.voids ratio


Question:
  
For testing a saturated clay for shear strength, the test recommended, is

1.direct shear test

2. triaxial compression test

3.unconfined compression test

4.all the above.


Question:
  
If drainage is permitted throughout the test, during the application of both normal, and shear stresses so that full consolidation occurs and no excess pore pressure is set up at any stage of the test, is known as

1. quick test

2.drained test

3.consolidated undrained test

4.none of these.


Question:
  
In a fow net

1.flow lines and equipotential lines cross each other at right angles

2.fields are rectangles whose length is twice the breadth

3.smaller the dimensions of the field, smaller will be the hydraulic gradient and velocity of flow through it

4.. for homogeneous soil, the curves are smooth and circular.


Question:
  
In a purely cohesive soil, the critical centre lies at the intersection of

1. perpendicular bisector of slope and the locus of the centre

2.perpendicular drawn at l/3rd slope from toe and the locus of the centre

3.perpendicular drawn at 2/3rd slope from toe and the locus of the centre

4.directional angles


Question:
  
In active state of plastic equilibrium in a non cohesive soil with horizontal ground surface

1.major principal stress is horizontal

2.minor principal stress is vertical

3.major principal stress is vertical

4.minor and major principal stresses are equally inclined to horizontal.


Question:
  
In non-cohesive soil in passive state of plastic equilibrium

1.major principal stress is horizontal

2.minor principal stress is vertical

3.major principal stress is vertical

4.minor and major principal stresses are equally inclined to the horizontal


Question:
  
Pick up the incorrect definition from the following:

1.Ratio of the compressive strength of unconfined undisturbed soil to that of remoulded soil, is known as the sensitivity of the soil sample

2.The rotation of soil particles into stable state while remoulding, is known as the thiostropy of soil

3.The water content at which a soil changes from the liquid state to solid state, is known liquid limit of the soil

4.The water content at which a soil flows, is known plastic limit of the soil


Question:
  
Stoke's law does not hold good if the size of particle is smaller than

1.0.0002 mm

2.0.002 mm

3.0.02 mm

4.0.2 mm


Question:
  
The ratio of the undrained strength in the undrained state to the undrained strength, at the same water content, in the remoulded state, is called the sensivity of the clay. Its value for quick clays is

1.4

2.8

3.12

4.20


Question:
  
The shear strength of a soil

1. increases with an increase in the normal stress

2.is proportional to the cohesion of the soil

3.is generally known as the strength of the soil

4.all the above.


Question:
  
The triaxial apparatus is usually used for

1.unconsolidated-undrained test

2.. consolidated-undrained test

3.drained test

4.all the above tests.


Question:
A clay subjected to pressure in excess to its present over-burden, is said to be

1.pre-compressed

2. pre-consolidated

3. over-consolidated

4.all the above.


Question:
A critical hydraulic gradient may occur when

1. flow is in upward direction

2.seepage pressure is in upward direction

3.effective pressure is zero

4.all the above.


Question:
A saturated soil sample has water content of 40% and specific gravity of soil particles 2.7. The void ratio of the soil, is

1.0.4

2.0.52

3.1.08

4.none of these.


Question:
A soil mass coated with a thin layer of paraffin weighs 460 g. When immersed, it displaces 299 cc of water. The weight of paraffin is 10 g. If specific gravity of solids is 2.5 and that of paraffin 0.9, the void ratio of soil, is

1.0.55

2.0.6

3.0.65

4.0.7


Question:
A soil sample of mass specific gravity 1.92, has a moisture content 30%. If the specific gravity of solids is 2.75, the degree of saturation, is

1.95.40%

2.95.50%

3.95.60%

4.95.70%


Question:
According to IS : 2720 - 1965, the composition of a dispersing solution used in pipette analysis for determining the size of particles, is

1. sodium-hexametaphosphate 33 g, sodium carbonate 7 g and distilled water one litre

2.sodium-hexametaphosphate 7 g, sodium carbonate 33 g and distilled water one litre

3.sodium-hexametaphosphate 23 g, sodium carbonate 17 g and distilled water one litre

4.none of these.


Question:
Cohesive soils are generally

1.plastic and also compressible

2.elastic and also compressible

3.plastic but incompressible

4. none of these.


Question:
Compression of soil occurs rapidly if voids are filled with

1.air

2.water

3.partly with air and partly with water

4.none of these.


Question:
Drift' is the material picked up, mixed, disintegrated, transported and redeposited by

1.wind

2.gravitational force

3.glaciated water

4.all the above.


Question:
For a base failure of a slope, depth factor

1.Df = 1

2.Df < 1

3.Df > 1

4.none of these.


Question:
For slopes of limited extent the surface of slippage, is usually along

1.a parabolic arc

2.an elliptical arc

3.a straight line

4.a circular arc.


Question:
he consolidation time for soils

1. increases with increasing compressibility

2.decreases with increasing permeability

3.increases rapidly with increasing size of soil mass

4. All the above.


Question:
The method of the slices is applicable to

1.homogenous soils

2. stratified soils

3.saturated soils

4.non-uniform slopes


Question:
Pick up the correct statement from the following:

1.A maximum value of dry density is obtained at optimum water content

2.At low value of water content most soils tend to be stiff.

3.At high water content, the dry density decreases with an increase of water content.

4.All the above.


Question:
Pick up the correct statement from the following:

1.The void ratio in soils is defined as the ratio of the volume of voids to the volume of solids

2.The porosity of a soil is defined as the ratio of the volume of voids to the gross volume of the soil

3. The bulk density of a soil is defined as the unit weight of the soil

4. All the above.


Question:
The angle of internal friction, is least for

1.angular-grained loose sand

2.angular -grained dense sand

3.round-grained loose sand

4.clays.


Question:
The consistency index of a soil is defined as the ratio of

1. liquid limit plus the natural water content to the plasticity index of the soil

2.liquid limit minus the natural water content to the plasticity index of the soil

3. natural water content of a soil minus plastic limit to the plasticity index of the soil

4. natural water content of a soil plus its plastic limit to the plasticity index of the soil.


Question:
The critical exist gradient of seepage water in soils, increases with

1.an increase in specific gravity

2.a decrease in specific gravity

3. a decrease in void ratio

4.none of these.


Question:
The inventor of the term soil mechanics, was

1.Kray

2.Dr. Karl Terzaghi

3.Leygue

4.Fellenius.


Question:
The minimum depth of building foundations on

1.sandy soils is 80 cm to 100 cm

2.clay soils is 90 cm to 160 cm

3. rocky soils is 5 cm to 50 cm

4.all the above.


Question:
The phreatic line in an earth dam may be

1.circuar

2.elliptical

3.parabolic

4.a straight line


Question:
The property of a soil which permits water to percolate through it, is called

1.moisture content

2.permeability

3.capillarity

4.none of these.


Question:
The ratio of the volume of water present in a given soil mass to the total volume of its voids, is known

1.porosity

2.void ratio

3.percentage voids

4. degree of saturation.


Question:
The reduction in volume of soil due to squeezing out of water from the voids, is termed

1.primary consolidation

2.primary compression

3.primary time effect

4. all the above.


Question:
The shearing strength of a cohesion-less soil depends upon 

1. dry density

2. rate of loading

3. confining pressure

4.nature of loading.


Question:
The total weight of a pycnometer with water and oven dried soil 20 (g) is 1600 g. The pycnometer filled with water alone weighs 1500 g. The specific gravity of the soil, is

1.1

2.1.5

3.2

4.2.5


Question:
The zero atmospheric pressure is at

1.sea level

2.mean sea level

3.water table

4.both (c) and (d) of the above.


Question:
When the seepage pressure becomes equal to the pressure due to submerged weight of a soil, the effective pressure is reduced to zero and the soil particles have a tendency to move up in the direction of flow. This phenomenon is generally known

1.quick condition

2.boiling condition

3.quick sand

4.all the above.


More MCQS

  1. Civil Engineering MCQS -Building Materials Section 1
  2. Civil Engineering MCQS -Building Materials Section 2
  3. Civil Engineering MCQS -Building Materials Section 3
  4. Civil Engineering MCQS -Building Materials Section 4
  5. Mechanical Engineering Engineering MCQS -Mechanics Section-1
  6. Mechanical Engineering Engineering MCQS -Mechanics Section-2
  7. Civil Engineering MCQS -Building Materials Section 5
  8. Civil Engineering MCQS -Building Materials Section 6
  9. Civil Engineering MCQS -Building Materials Section 7
  10. Civil Engineering MCQS -Building Materials Section 8
  11. Civil Engineering MCQS-Surveying Section 1
  12. Civil Engineering MCQS-Surveying Section 2
  13. Civil Engineering MCQS-Surveying Section 3
  14. Civil Engineering MCQS-Surveying Section 4
  15. Civil Engineering MCQS-Surveying Section 5
  16. Civil Engineering MCQS-Surveying Section 6
  17. Civil Engineering MCQS-Surveying Section 7
  18. Civil Engineering MCQS-Surveying Section 8
  19. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 1
  20. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 2
  21. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 3
  22. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 4
  23. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 5
  24. Civil Engineering (MCQS) Soil Mechanics and Foundation Engineering SET 6
  25. Civil Engineering [MCQS] Applied Mechanics Section -1
  26. Civil Engineering [MCQS] Applied Mechanics Section -2
  27. Civil Engineering [MCQS] Applied Mechanics Section -3
  28. Civil Engineering [MCQS] Applied Mechanics Section -4
  29. Civil Engineering [MCQS] Applied Mechanics Section -5
  30. Civil Engineering -MCQS-Hydraulics Section 1
  31. Civil Engineering -MCQS-Hydraulics Section 2
  32. Civil Engineering -MCQS-Hydraulics Section 3
  33. Civil Engineering -MCQS-Hydraulics Section 4
  34. Civil Engineering -MCQS-Hydraulics Section 5
  35. Civil Engineering -MCQS-Hydraulics Section 6
  36. Civil Engineering -MCQS-Waste Water Engineering - Section 1
  37. Civil Engineering -MCQS-Waste Water Engineering - Section 2
  38. Civil Engineering -MCQS-Waste Water Engineering - Section 3
  39. Civil -MCQ RCC Structures Design - Section 1
  40. Civil -MCQ RCC Structures Design - Section 2
  41. Civil -MCQ RCC Structures Design - Section 3
  42. Engineering Electrical Engineering Dc Motors part1
  43. Engineering Electrical Engineering Dc Motors part 2
  44. Engineering Electrical Engineering Dc Motors part3
  45. Electric Drives MCQ Questions and Answers
  46. Automobile Engineering MCQ Set 01
  47. Automobile Engineering MCQ Set 02
  48. Automobile Engineering MCQ Set 03
  49. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 01
  50. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 02
  51. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 03
  52. Compressors, Gas Turbines and Jet Engines MCQ Practice Test - Set 04
  53. Machine Design Mcq set 01
  54. Machine Design Mcq set 02
  55. Machine Design Mcq set 3
  56. Mechanical Engineering Design MCQ SET 03
  57. Mechanical Engineering Design MCQ SET 04
  58. Advanced Surveying mcq set 1
  59. Automobile Engineering MCQ
  60. Basic Civil Engineering Mcq
  61. Microwave Engineering Mcq Set 1
  62. Microwave Engineering Mcq Set 2
  63. Microwave Engineering Mcq Set 3
  64. Mechanical Engineering Basic Mcq Questions Set 1
  65. Mechanical Engineering Basic Mcq Questions Set 2
  66. Basic Chemical Engineering MCQ
  67. Chemical Engineering MCQ Question Set 1
  68. Chemical Engineering Mcq Question Set 2
  69. Chemical Engineering Mcq Question Set 3
  70. Chemical Engineering Mcq Question Set 4
  71. Chemical Engineering Mcq Question Set 5
  72. Chemical Engineering Mcq Question Set 6
  73. Chemical Engineering Mcq Question Set 7
  74. Chemical Engineering Mcq Question Set 8
  75. Civil Engineering Basic Set 1
  76. Chemical Engineering Mcq Question Set 9
  77. Chemical Engineering Mcq Question Set 10
  78. Civil Engineering Basic Set 2
  79. Chemical Engineering Mcq Question Set 11
  80. Chemical Engineering Mcq Question Set 12
  81. Engineering Electrical Engineering
  82. Chemical Engineering Mcq Question Set 14
  83. Chemical Engineering Mcq Question Set 15
  84. Chemical Engineering Mcq Question Set 16
  85. Chemical Engineering Mcq Question Set 17
  86. Engineering Electronics & Communication Engineering
  87. Engineering Computer Science & Engineering
  88. Computer Science & Engineering Computer Networks Mcq
  89. Environmental Engineering MCQ
  90. Microwave Engineering ECE Mcq
  91. Electrical Engineering Mcq
  92. Engineering Branch Wise MCQs
  93. Software Engineering Multiple Choice Questions
  94. Traffic Engineering MCQ
  95. Highway Engineering MCQs
  96. Engineering Thermodynamics MCQs
  97. Materials and Processes -Notch Toughness
  98. Software Engineering Multiple Choice Question Set 1
  99. Software Engineering Multiple Choice Question Set 2
  100. Software Engineering Multiple Choice Question Set 3
  101. Software Engineering Multiple Choice Question Set 4
  102. Hydraulic Machines MCQs Set-1
  103. Hydraulic Machines MCQs Set-2
  104. Hydraulic Machines MCQs Set-3
  105. Hydraulic Machines MCQs Set-4
  106. Basic Civil Engineering MCQ
Search
Olete Team
Online Exam TestTop Tutorials are Core Java,Hibernate ,Spring,Sturts.The content on Online Exam Testwebsite is done by expert team not only with the help of books but along with the strong professional knowledge in all context like coding,designing, marketing,etc!